⚡
Custom PCB Design
Schematic capture, multi-layer layout, signal & power integrity, and DFM-ready Gerbers. We design to IPC standards and your mechanical envelope.
- 2–12 layer boards
- High-density & flex-rigid
- Full fabrication package
CubeSat Avionics · Custom PCB Design · Flight Hardware
From a napkin sketch to an integrated, test-ready board. We design and deliver custom avionics and PCBs for 1U–12U CubeSats — power, command & data handling, attitude control, and payload interfaces. Send us your mission, get a quote in 24 hours.
What we do
You bring the mission requirements. We handle the electronics — from architecture to a board you can integrate and fly.
Schematic capture, multi-layer layout, signal & power integrity, and DFM-ready Gerbers. We design to IPC standards and your mechanical envelope.
Complete subsystem boards designed for the space environment — mechanically and electrically compatible with standard CubeSat stacks.
Prototype assembly, firmware bring-up support, and functional test. We hand you a board that powers on and talks to the bus on day one.
Have an existing design? We review schematics and layout, find the failure modes, and deliver a respin that works.
Hardware catalog
Reference designs we build, customize, and deliver. Every board is tailored to your mission — pricing is per-project, requested through a quote.
MPPT solar input, battery management, regulated 3.3V/5V/12V rails, and per-channel current monitoring with latch-off protection.
Request a quote →Low-power MCU/SoC, redundant non-volatile storage, watchdog, RTC, and a full set of bus interfaces for command & data handling.
Request a quote →IMU, sun sensors, magnetometer, and magnetorquer/reaction-wheel drivers on a single stackable board for pointing and detumble.
Request a quote →Half-duplex radio front-end with TNC interface, designed for amateur and licensed CubeSat downlink/uplink. Antenna deployment driver optional.
Request a quote →Carrier and breakout board to integrate cameras, sensors, or experiments into the stack with clean power and data isolation.
Request a quote →Stack backplane, inter-board harnessing, and a motherboard that ties your subsystems together to the CubeSat Design Spec.
Request a quote →Engagement models
Pick the starting point that fits your mission. Every engagement is quoted up front in USD — no hourly creep, no surprises.
from $1,500
You have a design — we make sure it works before you spend on fabrication.
from $4,500
A single flight-ready board — EPS, OBC, ADCS, comms, or payload interface — built to your spec.
Custom
A complete, integrated CubeSat bus — multiple subsystems designed to work together.
Indicative starting prices; final quote depends on layer count, complexity, and quantity. Universities & student teams — ask about academic pricing.
How it works
Send your requirements — form factor, power budget, interfaces, payload. A short call or email is enough to get started.
Within 24 hours you get a fixed-scope quote, a block diagram, and a timeline. No surprises, no hourly creep.
Schematic and layout with milestone reviews. You see and approve the design before anything is fabricated.
Fabrication, assembly, and functional test. You receive the board, the full design package, and a test report.
Why teams choose us
We do one thing: electronics for small satellites. That focus means you get hardware that fits the stack and the schedule.
Questions, answered
The things teams ask us before starting. Don’t see yours? Just ask.
Yes. You receive the full source design package — schematics, PCB layout source, Gerbers, drill files, BOM, and assembly drawings. No vendor lock-in, ever.
You get a fixed-scope quote within one business day. Prototype boards typically take 2–6 weeks depending on complexity, layer count, and fabrication queue.
Yes. We routinely work under NDA and treat your mission details and IP as strictly confidential. Send yours, or use ours.
We design in industry-standard EDA tools and deliver a complete, fab-ready package: schematics, layout source, Gerbers, drill files, BOM, pick-and-place files, and a functional test report.
Projects are quoted and invoiced in USD with milestone-based payments — typically a deposit to begin and the balance on delivery. No hidden hourly billing.
We focus on commercial, educational, and research hardware. If your program involves export-controlled or ITAR-regulated items, tell us up front so we can scope it correctly or point you to the right partner.
Absolutely. We hand off clean, documented design files and can coordinate directly with your CM, or manage fabrication and assembly for you — your choice.
Get in touch
Describe your mission and we’ll reply within one business day with next steps and a quote. No obligation.